Make sure the door arrow points toward the door. 6\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e9.\u003c\/strong\u003e Place the bullet and chain into the rail.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/37301R_Genie_Chain_Drive_Extension_Kit_Installation_Instructions_Figure_6_large.png?v=1559231894\" alt=\"Chain Drive Genie Extension kit 37301R Installation Instructions figure 6\"\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e10.\u003c\/strong\u003e At the door end of the rail, slide the carriage back into the rail. The door is 10' high, which opener and options are available? Insert two mounting screws and tighten with a 1\/4” wrench or socket. If so, call a trained professional for an. It is important that the pin be inserted from the bottom as shown. 9, 13. Proceed to step 3 on the Genie ChainDrive assembly & installation poster. At the door end of the rail, slide the carriage back into the rail. Fig. very slowly. evaluation and repairs, if needed. Fig. We no longer have the extension kit for the IC250/A model garage door opener. Fig. Do not begin Step 1G. Extension Kit for Tube Belt Drive Rail. Do you have extension kits for a model 2022 chain drive opener. This kit is designed specifically for Genie chain drive openers. Carefully remove the pulley pin. Genie PowerLift 1/2 HP Screw Drive Garage Door Opener. Check door height, 8' doors require a Rail Extension Kit (available at leading retail stores) Rail Assembly 2. high\u003c\/span\u003e \u003c\/li\u003e\n\u003cli\u003eModel EKCC                                                          \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c!-- TABS --\u003e\n\u003ch5\u003eReviews\u003c\/h5\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch5\u003eInstallation Instructions\u003c\/h5\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/37301R_Genie_Chain_Drive_Extension_Kit_Installation_Instructions.pdf?4258\" target=\"_blank\" rel=\"noopener noreferrer\"\u003e\u003cimg src=\"\/\/cdn.shopify.com\/s\/files\/1\/1470\/8272\/files\/PDF_ICON_icon.png?v=1533737947\" alt=\"\"\u003e Genie EKCC Chain Drive Rail Extension Kit Installation PDF Instructions \u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eEKCC (37301R) CHAIN RAIL EXTENSION KIT INSTALLATION INSTRUCTIONS \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePreparation:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eYou will need a Phillips Head Screwdriver, 7\/16” \u0026amp; 1\/4” wrench or socket. Position the chain through the alignment slots of the pulley guard. The extension kit for C-channel screw drive garage door opener rails is to be used in addition to a 7' (3-piece) screw drive rail … pmx-ic b series. Fig. Important: confirm the pulley pin is still in place. 6. you need extension brackets or wooden blocks to extend the Safe-T-Beam far enough off the wall to see past any door hardware? An improperly balanced door could cause severe injury. Position the chain through the alignment slots of the pulley guard. It is also recommended that T-handles be removed. 12.\u003cbr\u003eNote: This is also illustrated in step 1G on the assembly \u0026amp; installation poster.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e16.\u003c\/strong\u003e On the door end (pulley), tension the chain by tightening the adjustment nut on the pulley assembly until the chain does not ride on the rail (approximately 1\/8” off the rail. 1\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e2.\u003c\/strong\u003e Carefully remove the pulley pin. indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This is about the size of a 2" x 4". Proceed with the instructions below to attach the 37301R garage door opener rail extension. Do not begin Step 1G. see section 8 - Is there wood along the, door tracks near the floor where the Safe-T-Beam, can be most easily mounted, or will you need fasteners or some other material for mounting to the track itself? Check the balance of the door by manually lifting it halfway open and release. We have Genie rail extension kits for screw drive, belt drive and chain drive Genie garage door openers. Powerhead (drive sprocket) will be on your right.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e1.\u003c\/strong\u003e Slide pulley assembly out of the rail end. Fig. indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage. If you want to know more or withdraw your consent to all or some of the cookies, please refer to the. • do not allow children to play with the door operator. It is recommended that closed loop. This website or its third-party tools use cookies, which are necessary to its functioning and required to achieve the purposes illustrated in the cookie policy. Genie Chain Drive Garage Door Opener 8ft Rail Extension Kit - Extends Your Tube-Style Chain Drive Rails to Fit an 8-Foot Garage Door - Compatible with All Genie Tube-Style Chain Drive Models, EKTC. We no longer have the extension kit for the GCG350ML model garage door opener. 1e. FREE Shipping by Amazon. INCLUDES: rail extension, 8 FT belt, easy-to-follow instructions ... Genie Chain Drive Garage Door Opener 8ft Rail Extension Kit - Extends Your Tube-Style Chain Drive Rails to Fit an 8-Foot Garage Door - Compatible with All Genie Tube-Style Chain Drive Models, EKTC 4.7 out of 5 stars 170. do not ATTEMPT TO ADJUST SPRINGS OR THEIR ATTACHED PARTS! The holes in the ends of the pulley assembly should match up with the mounting holes at the end of the rail. Make sure the door arrow points toward the door. Begin by completing steps 1A through 1F on the Assembly\/Installation Poster.